A precision made laser cut zinc plated steel template comb for the CDJ300. A 12.7 mm (1/2 inch) box joint. This product includes: 1 x Template comb 1 x 15.8 mm Guide bush

Template for making through dovetails. The template is dual-sided. This item has been discontinued and will not be available after these have been sold out

Guide bush guides the router when using a template. Fits directly to Trend T3, T4, T5, T5 MK2, T9, T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

A unique concept which allows oval pockets to be routed, to disguise ugly resin pockets and knots in timber. This is especially required when softwoods are being used. Can be used to repair blown worktop joints when care is used to ensure the plug is glued in perfectly level. See Knowledge for details. The template is supplied with a 10 mm diameter 1/4 inch shank cutter, a 20 mm template guide bush and a 40 mm inlay collar. Unibase may be required for certain makes & models of router.

Will also fit the following machines:- Atlas Copco (AEG) OFSE2000, Freud FT2000E,FT2200E, FT3000VCE, Casals FT2000VCE.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. It's directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

The collet is a one-piece multi-slit design to provide maximum grip on to the surface of the cutter's shank. Does not include the collet nut.

This teardrop-shaped base is fitted to the router and allows better control when edge moulding, by preventing router tilt. Large knob for greater control. Pre-drilled for Trend, Elu and DeWalt routers. Can be re-drilled by the user to suit other makes of routers. Made from clear plastic. This product includes: 1 x Teardrop-shaped base 1 x Knob assembly 2 x Fixing screws This teardrop-shaped base is fitted to the router and allows better control when edge moulding, by preventing router tilt. Large knob for greater control. Pre-drilled for Trend, Elu and DeWalt routers. Can be re-drilled by the user to suit other makes of routers. Made from clear plastic. This product includes: 1 x Teardrop-shaped base 1 x Knob assembly 2 x Fixing screws

Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Trend GB20 Guide bush 20 mm diameter Guide bush guides the router when using a template. Fits directly to Trend T3, T4, T5, T5 MK2, T9, T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

Template for making holes for dowelling at 32 mm centres This item has been discontinued and will not be available after these have been sold out

These kits fit on the DC400 and enables you to extract the dust. This item has been discontinued and will not be available after these have been sold out

Aluminium collar to fit guide bushes. Enables single shaped templates to be used to cut perfectly matching pocket & inlay. Collars have integral rubber 'O' rings to ensure collar secures onto guide bush. Templates should be made with suitable sized corners for the collar being used. The correct diameter straight cutter as indicated should always be used. Guide bush not included.

A precision multi-slit one piece collet. Does not include the collet nut. For Trend T10 and T11 routers.

This height adjuster simply fits onto the router and allows fine adjustments of the cutter height. They are especially useful for accurate work such as when the router is held inverted in a router table. Suitable for the following: Trend T3, T5, T5MK2

One piece collet for the T3. Does not include the collet nut.

This item has been discontinued and will not be available after these have been sold out

Twenty degree finger set for the DC400 dovetailing centre.

Fourteen degree finger set for the DC400 dovetailing centre.

Range of small diameter shank cutters for Mini CNC router carving machines. For carving. Two flute v groove.

Replacement fence rod for the T5.

A two part trade hinge jig to cut hinge recesses in doors & linings using a plunge router. Two part, splits into two lengths with jointing plate. Hard wearing template in 12 mm phenolic plastic. One set up for door and frame. No need to adjust for repeated doors. Four adjustable apertures. For a 2-metre door hinges are 6 inch down and 9 inch up and the middle. Fourth hinge for fire doors (355 mm /14 inches down from top of top hinge). For doors 16 mm to 51 mm thick with separate (plant on) stops, or stops thinner than 11 mm. Swivel end plate for 3 mm gap to head of door. Use with a light duty plunge router with 1/4 inch collet. Includes three edge guides, three brad awls and 16 mm guide bush. Unibase may be needed. T4EK router requires a ref. UNIBASE or special guide bush ref. GB/T4/160. 3 x Bradawl with spacers 3 x Edge guides 1 x 16 mm guide bush 1 x Hex key 1 x Carry case

This product includes: 5 x9 degree angled pin guides Nine degree finger set for the DC400 dovetailing centre.

Seven degree finger set for the DC400 dovetailing centre. This product includes: 5 x7 degree angled pin guides

A half blind guide set for DC400 dovetailing centre. This product includes: 5 x Lapped Pin Guides

A common tail guide set for DC400 dovetailing centre. This product includes: 5 x Common tail guide

Comprises three sets of cams, bolts & fixings. This accessory is intended to be used with only a T11 plunge router and router tables such as the Trend PRT router table or as a retro-fit to other suitable accessories to allow the T11 router to be fitted and removed quickly. The kit can be retro-fitted to certain tables including user-made tables or jigs as long as the table surface is no less than 8mm thick and there is sufficient room to turn the cam levers fully.

Replacement knob for the Pivot Jigs. This item has been discontinued and will not be available after these have been sold out

Clear 6 mm plastic inlay templates for use with an inlay kit fitted to a plunge router. Inlay kit allows a shaped pocket and matching inlay patch to be routed easily with a router cutter to create perfect inlays. A Unibase may be required for certain makes and models of router.

An annealed steel reduction collar 42 mm to 43 mm to allow T3 routers to be fitted into 43 mm drill stands to become a fixed head router. Can be used with Power Devil PDW5026 and Ferm FBF-6E. This item has been discontinued and will not be available after these have been sold out

Contractor jig with interchangeable templates for use with a plunge router to cut the mortise & face-plate for larger locks quickly & accurately. Suitable for DDA (Disability Discrimination Act) lock size. 20 mm x 235 mm radius end faceplate, 24 mm x 235 mm radius end faceplate and 17 mm x 170 mm mortise. Adaptor plate included allowing smaller templates (239 mm x 60 mm) to be fitted (as supplied with standard LOCK/JIG). Suitable for doors 34 mm to 58 mm thick. An auger bit and drill are required to complete deep mortises. The jig requires a 1/2- inch plunge router with an 80 mm plunge, fitted with a 30 mm guide bush with 6 mm spigot & 12 mm diameter long reach cutter. A 1/4-inch plunge router can be used for the faceplate but will not achieve full depth of mortise. Suits DIN style locks. 1 x Guide bush collar 2 x Faceplate template 1 x Mortise template 1 x Template adaptor 6 x Spacer Fingers

Guide bush guides the router when using a template. Fits directly to Trend T3, T4, T5, T5 MK2, T9, T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.

This classic style inlay design (also known as Bow- Tie) works great for everything from decorative touches to your project to reinforcement of joints. Add decorative butterfly accents to your projects with ease in minutes.Great for repairing imperfections and knots in wood. These Acrylics Butterfly Inlay Template Set are easy to use and have a clear and transparent appearance that ensures precision and visibility of the work Designed to work with our brass inlay kit, these two template sets contain butterfly inlay templates of varying sizes. The large butterfly template has 3 inlay templates ranging in length from 3-5/32" to 4-3/4". The small butterfly template has 4 inlay templates ranging in length from 1-11/16" up to 2-1/2".

This collet extension can be used with all 1/2″ shank routers and will lift the cutter by an additional 60mm. When working with a router table that has a table made of thick material, typically the cast iron type or homemade tables, a collet extension may be required. A 19mm and a 22mm spanner are required to tighten the collet.

Rubber-like "wonder" mat grabs onto your bench top and holds small parts while you route decorative edges or finish-sand them. Protects finishes and eliminates need for complex holding jigs!

Our portable router table packed with the necessary features to maximise the versatility The Portable Benchtop Router Table features unmatched versatility. Large laminated MDF table-Helps users make smooth and precise cuts. The top is High Pressure Plastic Laminated & Bottom side is also laminated to prevent warping and to keep moisture out.

Metric & Inch Step Depth Gauge for Router and Table Saw, Aluminum Height Gauge Measuring Tool Ruler for Setting Up Blade Height.