Unique support ledge High-impact polymer handle Permanently etched stainless steel blade

Easy to read vial Magnetic lock adjustment Stainless steel blade with permanently etched ruler markings (in. and cm) 5 milled sides for superior accuracy Easy Grip™ magnet-held stainless steel scribe

The Kapro #444 Ergocast™ moulded Rafter Square is a value for money 180mm Square with easy to read graduations and a ledge base for efficient layout and marking.

The Ryder Try Square has a rosewood handle, brass wear plates and brass rivets for rigidity and a tempered blade. The Ryder try square has double sided wear plates on the handle.

The Ryder adjustable bevel is made with a rosewood handle and forged brass wingnut and end caps. A hardened steel blade for holding angles between 0-180 deg. The adjustable blade allows you to mark out preset angles or transfer angles from one workpiece to another.

This is a square that you can use with confidence, day in day out. Designed and constructed for everyday use, this reliable square should always be close to hand at the top of your toolbox.

A marking gauge is for general layout work. Gauge made with brass screws and hardened spur. The gauge needs to be tilted just right to the side to avoid pin chatter to maintain your line.

These vessel callipers are designed for internal and thin-wall dimensioning. The straight arm is especially useful for accessing narrow vessels. Sizes can be read at either end. Available in 2½", 5" and 10" models.

These vessel callipers are designed for internal and thin-wall dimensioning. The straight arm is especially useful for accessing narrow vessels. Sizes can be read at either end. Available in 2½", 5" and 10" models.

The design of these callipers allows not only the measurement of wall thickness but also inside dimensions like the size of an aperture. As with double ended callipers the measurement at one end automatically transfers to the opposite. Available in 6" and 8½" models.

The graduated square is precision ground and blade hardened. The beams and blade are ground for parallelism. The accuracies is less than 0.001" deviation per inch over the entire length of the blade. Extremely useful for setting up workshop equipment.

The graduated square is precision ground and blade hardened. The beams and blade are ground for parallelism. The accuracies is less than 0.001" deviation per inch over the entire length of the blade. Extremely useful for setting up workshop equipment.

The graduated square is precision ground and blade hardened. The beams and blade are ground for parallelism. The accuracies is less than 0.001" deviation per inch over the entire length of the blade. Extremely useful for setting up workshop equipment.

These vessel callipers are designed for internal and thin-wall dimensioning. The straight arm is especially useful for accessing narrow vessels. Sizes can be read at either end. Available in 2½", 5" and 10" models.

These are an indispensable addition to the turner's armoury for measuring both wall thickness and diameters. Because of their design the measurement taken at one end automatically transfers to the opposite end. This enables the turners to take an accurate measurement reading without the need to remove the callipers. Available in 4" and 7" models. The 7" version has an increased depth of throat at one end which permits the callipers to be used in large diameter vessels which have restricted openings.

The design of these callipers allows not only the measurement of wall thickness but also inside dimensions like the size of an aperture. As with double ended callipers the measurement at one end automatically transfers to the opposite. Available in 6" and 8½" models.

These are an indispensable addition to the turner's armoury for measuring both wall thickness and diameters. Because of their design the measurement taken at one end automatically transfers to the opposite end. This enables the turners to take an accurate measurement reading without the need to remove the callipers. Available in 4" and 7" models. The 7" version has an increased depth of throat at one end which permits the callipers to be used in large diameter vessels which have restricted openings.

Here's a solution that's so simple, you'll wonder why it took so long to develop! The Clamp-It® replaces custom clamping jigs, acts as a third hand, and eliminates the need for long bulky clamps. Simply put, the Clamp-It® is a square you can clamp. In fact, you can even assemble a cabinet one corner at a time! Works with any joinery technique, from nails to hand cut dovetails. It's ideal for every stage of construction, from assembling plywood cabinets to face frames and drawers. Clamp-It® is also perfect for framing decks and installing rails and balusters. Attach it to a work surface, and it becomes a right angle fixture for bench assembly. Clamp-It® is computer designed and manufactured from high impact, rigid polycarbonate to ensure strength and accuracy. Size of the Clamp-It® is 8" X 8" X 1 - 1/2". Great for: Drawer Assembly: Clamp-It® is designed for use on either the inside or outside of a corner, making it ideal for assembling drawers with lipped fronts. Deck Rails: Use Clamp-It® to hold deck balusters at a perfect 90° angle while fastening. Bench Jigs: Clamp-It® can be secured to any work surface to create a simple 90° assembly jig. Includes: 1 x Clamp-It® Assembly Square

The Marathon Combination Square 300m has a Clearly Marked Scale that is High Wear Resistance it Includes a Heavy Duty Scriber.

This center finder is perfect for laying out bowls, trays, and platters Finding the center of irregular shapes to optimize yield is simple and easy Made from 1/8" acrylic with a center hole and clearly marked circles in 1/4" increments To use, position on a blank, find the center, push an awl in the center hole and then trace a circle around the pivot point Will mark circles up to 10" in 1/2" increments