Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Used on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature

V point through hole slow spiral TCT drills can be used in drilling machines or portable routers. Tungsten Carbide Tipped for long life. Router drilling ensures hole is perpendicular to surface.

Straight Bit - Solid Carbide 2.4mm Diameter X 1/2"High - Shank: 1/4"

Straight Bit Single Flute Metric 3mm Diameter X 13mm Long - Shank: 1/4"

Straight Bit - 2 Flute Solid Carbide 3mm X 1/2" High - Shank: 1/4"

Straight Bit Single 1/8" Diameter X 1/2"High- Shank: 1/4"

Straight Bit - 2 Flute - Solid Carbide 1/8"(3.2mm) X 1/2" High - Shank: 1/4"

Straight Bit Solid Carbide 4mm Diameter X 1/2" High -Shank: 1/4"

Straight Bit Single Flute 3/16" (4.8mm) Diameterx 1/2"High - Shank: 1/4"

Straight Bit - 2 Flute 5 Diameter X 12mm Long Shank: 1/4"

Straight Bit - 2 Flute - 1/4" Diameter X 3/4" High- Shank: 1/4"

Straight Bit - 2 Flute 1/4"Diameter X 1" High - Shank: 1/4"

Straight Bit - 2 Flute Metric 8mm Diameter X 24mm Long- Shank: 1/4"

Straight Bit - 2 Flute - 3/8"(9.6mm) Diameter X 1" High - Shank: 1/4"

Straight Bit - 2 Flute 3/8 Diameter X 32 Long - Shank: 1/4"

Straight Bit - 2 Flute Metric 10mm Diameter X 25mm Long - Shank: 1/4"

Straight Bit - 2 Flute Metric 14mm Diameter X 25mm Long - Shank: 1/4"

Straight Bit - 2 Flute- 20mm Wide X 20mm High -Shank: 1/4"

Straight Bit - 2 Flute 7/8" (11.2mm) Wide X 3/4" High - Shank: 1/4"

Straight Bit 2 Flute 1" Diameter X 3/4" High - Shank: 1/4"

Toolmate Combination Pilot Panel 1/4"X 3/4" - Shank: 1/4"

Trim Bit 1/4"Diameter X 3/4" High With Ball Bearing - Shank: 1/4"

Trim Bit 3/8" Diameter X 1" Long - Shank: 1/4"

Dynabit Laminate Trim 1/2" Diameter X 1" Long- Shank: 1/4"

Pattern Flush Trim With Shank Bearing 1/2" Diameter X 1"- Shank: 1/4"

Bevel Trim Bottom Bearing 45 Deg X 1/4" High - Shank: 1/4"

Dovetail Bit 1/2"Wide X 1/2" High - Shank: 1/4"

V-Groove 90 Diameter 3/8" Wide X 1/2" Deep - Shank: 1/4"

V-Groove 90 Diameter 1/2" Wide X 1/2" Deep - Shank: 1/4"

V-Groove 90 Diameter 5/8" Wide X 5/8" Deep - Shank: 1/4"

V-Groove -1/2" Diameter X 5/8" High X 60 Degrees - Shank: 1/4"

Quirk Topped Ogee 3/16" Radius - Shank: 1/4"

Fine finish on both sides of solid timber. Ideal for edge trimming. For use on 16mm boards. Single fluted compression spirals.

Toolmate Cove Bit 7/8" X 1/4" Radius - Shank: 1/4"

Toolmate Classical Ogee 9/16" Deep - Shank: 1/4"

Quirk Topped Ogee 1/4"Radius - Shank: 1/4"

Toolmate R/Nose Vein Bit 1/4" X5/16" X 1/4" Sh

These dovetail cutters produce a tight reliable joint for drawers, boxes etc. Refs. C154 & C041A can be used with Trend CDJ300, CDJ600 & DJ300 dovetail jigs. To suit user preference, the table shows angles from the horizontal and the profiles show angles from the vertical. These cutters have Solid Carbide inserts.

Gives a narrow appearance to a board edge.

TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges.

The glazing bar ovolo cutter is bearing guided to speed setting-up and to enable curved frames to be moulded.

Protec 1/2" OD X 1/4" ID

Pro Tech Classic 1 1/2" Wide X 5/8" Deep - Shank: 1/4"