The Tork Craft Router Bit 1/2" Shank Set, for hard and softwood, sealed ball bearing provides smooth cutting of timbers. 12 Piece set of 1/2" shank tungsten carbide tipped router bits, buts can be resharpened. All bits can cut hardwood, medium density fireboards, and chipboard. Convenient, secure storage, and carry case. Hard / Soft Wood Sealed Bearings Tungsten Carbide Tipped All bits can be resharpened Convenient, secure storage and carry case
Tool steel plug/pellet cutter. Use in a pillar drill to allow plugs to be made to cover the pocket hole pockets. Allows plugs up to 52 mm long to be created in end grain. Using the same timber as the project ensures the plug matches.
This teardrop-shaped base is fitted to the router and allows better control when edge moulding, by preventing router tilt. Large knob for greater control. Pre-drilled for Trend, Elu and DeWalt routers. Can be re-drilled by the user to suit other makes of routers. Made from clear plastic. This product includes: 1 x Teardrop-shaped base 1 x Knob assembly 2 x Fixing screws This teardrop-shaped base is fitted to the router and allows better control when edge moulding, by preventing router tilt. Large knob for greater control. Pre-drilled for Trend, Elu and DeWalt routers. Can be re-drilled by the user to suit other makes of routers. Made from clear plastic. This product includes: 1 x Teardrop-shaped base 1 x Knob assembly 2 x Fixing screws
The side fence has a fine micro adjuster to enable precise adjustment of the position of the cut. The fence cheeks are wide to provide good support and adjustable to suit the size of the cutter. An optional second fence will provide extra support when edging or mortising narrow timber. The plastic sliding cheeks can be adjusted to reduce the cutter aperture. A fence can be used with Elu MOF96, Dewalt DW613, DW615 and other similar routers with fence rods of 8 mm diameter and 84 mm centres.
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Used on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Used on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature.
Guide bush guides the router when using a template. Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.
Trend GB20 Guide bush 20 mm diameter Guide bush guides the router when using a template. Fits directly to Trend T3, T4, T5, T5 MK2, T9, T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.
Clear 6 mm plastic inlay templates for use with an inlay kit fitted to a plunge router. Inlay kit allows a shaped pocket and matching inlay patch to be routed easily with a router cutter to create perfect inlays. A Unibase may be required for certain makes and models of router.
An annealed steel reduction collar 42 mm to 43 mm to allow T3 routers to be fitted into 43 mm drill stands to become a fixed head router. Can be used with Power Devil PDW5026 and Ferm FBF-6E. This item has been discontinued and will not be available after these have been sold out
Trend 46/05X1/4TC Guided trimmer 6.3 mm diameter 12.7 mm length Two flute mini-trim with guide bearing will profile intricate shapes. Max. 2.0 mm trimming
V point through hole slow spiral TCT drills can be used in drilling machines or portable routers. Tungsten Carbide Tipped for long life. Router drilling ensures hole is perpendicular to surface.
Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Used on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature.
These dovetail cutters produce a tight reliable joint for drawers, boxes etc. Refs. C154 & C041A can be used with Trend CDJ300, CDJ600 & DJ300 dovetail jigs. To suit user preference, the table shows angles from the horizontal and the profiles show angles from the vertical. These cutters have Solid Carbide inserts.
Clear 6mm plastic inlay templates for use with an inlay kit fitted to a plunge router. Inlay kit allows a shaped pocket and matching inlay patch to be routed easily with a router cutter to create perfect inlays. A Unibase may be required for certain makes and models of router.
A two part trade hinge jig to cut hinge recesses in doors & linings using a plunge router. Two part, splits into two lengths with jointing plate. Hard wearing template in 12 mm phenolic plastic. One set up for door and frame. No need to adjust for repeated doors. Four adjustable apertures. For a 2-metre door hinges are 6 inch down and 9 inch up and the middle. Fourth hinge for fire doors (355 mm /14 inches down from top of top hinge). For doors 16 mm to 51 mm thick with separate (plant on) stops, or stops thinner than 11 mm. Swivel end plate for 3 mm gap to head of door. Use with a light duty plunge router with 1/4 inch collet. Includes three edge guides, three brad awls and 16 mm guide bush. Unibase may be needed. T4EK router requires a ref. UNIBASE or special guide bush ref. GB/T4/160. 3 x Bradawl with spacers 3 x Edge guides 1 x 16 mm guide bush 1 x Hex key 1 x Carry case
This router compass is used for cutting circles & arcs from 100 mm up to 610 mm radius. Made of clear plastic. Printed graduated scale for precise radius setting. Fits to the base of a router. Router not included. Plate has a 30 mm hole to allow a 30 mm guide bush to locate. 1 x Main Plate 1 x 'V' Pivot Point 1 x 4 mm Pivot Point 2 x Fixing screws
For the fast and accurate joining of timber and plywood giving strong instant joints. Supplied with two bases short and long. The long base is used on edge of the component, the short base allows jointing into corners for refurbishment work. Solid bushes with a variable pitch of 18 mm to 54 mm with sight arrows to aid pitch setting. Use on timber, MDF, plywood and blockboard. Allows a variety of joints to be created individually. Square drive self-tapping screws for use with a No.2 square drive bit to resist slipping (cam-out). The workpiece can be handled immediately after glueing & screwing creating time-saving benefits. Requires a clamp to secure mini pocket hole jig to the component. 50 x Dome head screws 1 x Long base 1 x Short base 1 x HSS drill bit with collar 1 x 150 mm Square drive bit 1 x Hex key 4 mm A/F 1 x Hex key 2.5 mm A/F
Comprises three sets of cams, bolts & fixings. This accessory is intended to be used with only a T11 plunge router and router tables such as the Trend PRT router table or as a retro-fit to other suitable accessories to allow the T11 router to be fitted and removed quickly. The kit can be retro-fitted to certain tables including user-made tables or jigs as long as the table surface is no less than 8mm thick and there is sufficient room to turn the cam levers fully.
A template to allow routing or drilling of 32 mm centre holes for 5 mm diameter shelf supports. The template is a clear plastic with an adjustable clamping bar with two locking knobs. Supplied with twelve 5 mm metal shelf supports, one alloy knurled index pin and a 9.5 mm diameter guide bush. Allows holes to be positioned from 10 mm to 64 mm from edge of board. This template can be used to add existing holes to a unit, or for user made shelves, the index lines to allow for easy setting up. Template can also be used with a power drill and an accessory quick release 5 mm shelf support drill bit guide Ref. SNAP/SS/5MM or TEMP/SSD/5MM. This bit has a lip and spur drill fitted for drilling blind holes. Requires two clamps and 5 mm TCT router dowel drill Ref. 61/05 or C174. 12 x Plain Metal Shelf Supports 1 x Knurled Index Pin 1 x 9.5 mm (3/8") Template Guide Bush