Cutting a smooth radius to soften a 90° corner is fast and flawless with our Corner Radius Routing Templates. The templates can be used alone to draft a simple pencil line, or, better yet, you can click them onto the included handle and rout the radius on your router table with no need for pencil lines at all. The bottom of each template has grippy rubber strips, which, combined with the handle, provide a solid grip that firmly straddles the corner of your workpiece. You get a wide range of a dozen total radiuses: 1/8'' through 1'' radiuses, in 1/8'' increments, and 1-1/4'' through 2'' radiuses, in 1/4'' increments. They're the perfect solution for any project with quarter-round corners, such as the armrests on Adirondack chairs, bookcase end panels, tabletops, wall-mounted shelves and more.

Here's a solution that's so simple, you'll wonder why it took so long to develop! The Clamp-It® replaces custom clamping jigs, acts as a third hand, and eliminates the need for long bulky clamps. Simply put, the Clamp-It® is a square you can clamp. In fact, you can even assemble a cabinet one corner at a time! Works with any joinery technique, from nails to hand cut dovetails. It's ideal for every stage of construction, from assembling plywood cabinets to face frames and drawers. Clamp-It® is also perfect for framing decks and installing rails and balusters. Attach it to a work surface, and it becomes a right angle fixture for bench assembly. Clamp-It® is computer designed and manufactured from high impact, rigid polycarbonate to ensure strength and accuracy. Size of the Clamp-It® is 8" X 8" X 1 - 1/2". Great for: Drawer Assembly: Clamp-It® is designed for use on either the inside or outside of a corner, making it ideal for assembling drawers with lipped fronts. Deck Rails: Use Clamp-It® to hold deck balusters at a perfect 90° angle while fastening. Bench Jigs: Clamp-It® can be secured to any work surface to create a simple 90° assembly jig. Includes: 1 x Clamp-It® Assembly Square

Our Center/Offset Marking Tool straddles your board to mark a perfectly centred line along the face or edge of boards up to 1-1/2'' wide or thick. Just insert your pencil into the centre hole, rotate the tool so the guideposts contact the material, then scribe. Alternatively, you can use a pencil in the notches to mark lines from 1/16'' to 1/2'' from the edge in precise 1/16'' increments. It's great for marking out mortises and rabbets, or for making reference lines for drilling holes. The tool accepts standard wooden pencils and has an onboard pencil storage slot. An embedded magnet lets you store it on any ferrous metal surface, such as a power tool, tool chest or magnetic storage strip. Includes: 1 x Rockler Center/Offset Marking Tool

In response to the rave reviews for our Silicone Glue Brush, Rockler is now offering the brush bundled with our flexible Silicone Tray and Silicone Spreader, all featuring the same easy cleanup as the original brush. The spreader is ideal for evenly distributing glue over broad surfaces, such as when glueing up plinth blocks, corbels or thick table legs. One swipe with the spreader leaves neat rows of "raked" glue, which fill in after a few seconds for perfect distribution. When you're done with your glue up, just rinse with water, or simply set it aside, and the glue will easily flake off by the following day. The Silicone Tray features a small saddle in the end, which holds your brush so that any stray drips go back into the pan when you're not brushing.

Sawhorses are incredibly practical when you need a lightweight, portable work surface, but if you've used them much, you know that workpieces tend to rattle around and get scratched while you saw, rout and sand. With the Bench Cookie® Plus Sawhorse Clips, that's no longer a problem. Simply slip the clips over your sawhorses, spin your Bench Cookies® Plus on, and you have a no-mar, no-slip work surface that is easily resizeable for any workpiece. The grip is so secure, it's almost like having a fully equipped workbench with dog holes and a vice. Plus, you can slip some Bench Cookie. Finishing Cones, on for an ideal finishing surface with no worries about dripping stain on your nice workbench.

Use Bench Cookie® Plus Work Grippers alone on the bench to grip and protect your workpieces, or use them with the included standard risers and XL risers to fix them to your dog holes or to allow space for a router bit or jigsaw blade beneath the workpiece. The Master Kit even includes eight Bench Cookie® Finishing Cones – the perfect perches for your projects while spraying or finishing. Everything you need to grip and protect your workpiece in your shop or on the job site!

Lift, grip, protect and finish your project with Bench Cookie® Work Grippers and Bench Cookie® Finishing Cones! Rockler Bench Cookie® Finishing Cones lift your project off your bench with minimal surface contact, keeping it stable during the entire finishing process! Custom sized to fit snugly over the incredibly popular Rockler Bench Cookie® Work Grippers. Team a set of Bench Cookie® Finishing Cones with a set of Bench Cookie® Work Grippers for a fail-safe project finishing system. Includes: 4 x Bench Cookie® Finishing Cones

Struggling to hold cabinet parts in alignment while driving fasteners can be an exercise in frustration, and if you're using a nail gun, downright dangerous. The Rockler Clamp-It® Corner Clamping Jig eliminates that frustration by providing another set of ''hands'' to hold your parts together. It's used with the enormously popular Clamp-It® (#29190, sold separately) to hold panels at a precise right angle for fastening. Used in sets of four, the jigs are supportive enough to hold an entire case assembly as it is being assembled. The clamps have soft pads to prevent workpiece marring. Mounting holes in the jig allow for attachment to your work surface. Includes: 1 x Rockler Clamp-It® Corner Clamping Jig 2 x 1'' Screws for Attaching Clamp-It (#29190 not included)