Close
Filters

Chestnut Spirit Stain Sample Pack

Chestnut Spirit Stain Sample Pack

R675,00 incl VAT
Can be used to try the colour or for use as a mixer to make a new colour or for use as a wash. Trial bottles are ideal for use when mixing with Cellulose Sanding Sealer and Melamine Lacquer to make tinted finishes.
- +
Manufacturer: Chestnut
Availability: In stock
SKU: PACSAMR
Manufacturer part number: 0

Specifications

Typical uses

  • To colour wood prior to finishing

Method of application

  • Cloth, brush, spray, foam brush

Drying Time

  • Usually within five minutes

Coverage

  • approximately 4-8 sq.m per litre

Compatibility

  • Use under most products; care should be taken when using under solvent-based finishes

Tips

  • Ensure wood is clean and dry before use. All colours can be intermixed or thinned for delicate wash effects.

Thinners

 

Safety Considerations

  • Highly Flammable
Write your own review
  • Product can be reviewed only after purchasing it
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
Customers who bought this item also bought
MAKITA DA3010F ANGLE DRILL ONLINE SOUTH AFRICA

MAKITA DA3010F ANGLE DRILL - NON-HAMMER

PP3010F
Makita angle drill will allow you to work in tight spaces where other drills just can't operate due to its 90-degree chick design. Compact and lightweight. 450W. Only 66mm in head height. Features a built-in LED job light. With keyed chuck. All ball-bearing construction ensures high durability. Double Insulation, Variable Speed, Reversing and Built-In Job Light.
Call for pricing
WOODOC INKY BLUE COLOUR 25ML south africa

WOODOC INKY BLUE COLOUR 25ML

PA-INKY
Woodoc colour is best used on wooden floors, wooden patio furniture, wooden toys, pine furniture, garage doors and gates.
R38,50 incl VAT
WOODOC KALAHARI RED COLOUR 25ML south africa

WOODOC KALAHARI RED COLOUR 25ML

PA-KALA
Woodoc colour is best used on wooden floors, wooden patio furniture, wooden toys, pine furniture, garage doors and gates.
R38,50 incl VAT
Picture of DREMEL DIAMOND TIP POINT 2.4MM

DREMEL DIAMOND TIP POINT 2.4MM

TA-7144
R175,00 incl VAT
CHESTNUT 500ML FOOD SAFE FINISH SOUTH AFRICA

Chestnut 500ml Food Safe Finish

PACNFSF
Food Safe Finish is clear, food-grade mineral oil. We use a thin grade of oil to allow it to soak into bare timber which then protects it against water splashes etc, whilst not tainting or affecting the food in any way. It dries to a fairly matt finish; it is, however, ideal to use for wet sanding and when used with a very fine abrasive it can give an exceptionally smooth surface that has its own gentle glow. Apply with a clean cloth or brush direct onto bare wood, up to three coats are recommended. If the oil sits on the surface and won’t soak in it means the timber has absorbed as much as it can and no further coats are needed. Any surplus can be removed with a clean cloth if required. Depending on the way the item is used it might be necessary to top-up the finish, especially if it is washed regularly.
R380,00 incl VAT
CHESTNUT 500ML FRICTION POLISH SOUTH AFRICA

Chestnut 500ml Friction Polish

PACNFP5
Friction Polish is a shellac-based polish ideal for creating a high gloss finish on or off the lathe. It’s a great decorative finish and is ideal for small items but can be difficult to apply to larger items on the lathe (over about 8-inch diameter). The high amount of shellac in Friction Polish does two main things. Firstly it helps seal bare wood and give it a great shine, which is good. Sadly the price of this commodity shot up a few years ago when the shellac crop failed and it never went back down, meaning that the cost of the polish has also risen sharply. Nevertheless, Friction Polish remains one of the most popular finishes for turners. It can be applied to bare wood but is normally used over a sealer and any of the sealers in the Chestnut Products range are suitable for this. Applied with the lathe running it dries almost instantly and builds to a deep, rich shine very quickly. Avoid using too much as this can cause ‘rings’ to appear on the surface. Friction Polish can be applied off the lathe with great success, using it like a French-Polish and rubbing it into the surface. This does require a large amount of elbow grease (sadly not something we supply) but the end result is well worth the effort!
R575,00 incl VAT