90 degree angled screwdriver attachment allows access to tight corners.
Quick change chuck ensure tool is held securely.
Use with bit holders, direct drive or insert screwdriver bits, hex drills and drill/countersinks.
Two position handle for maximum control.
Heat treated steel precision gears for maximum torque.
Die cast head with ball bearing guides for stability. Use in cordless and corded drills.
Can be used with impact screwdrivers with following specification - maximum 12v, maximum torque 80nm (816 kgf.cm), rotation 0-2000 rpm and 0-2500 impacts per min.
Maximum 60 Nm torque (612 kgf cm).
Do not use with nut drivers.
1 x No 2 Pozi 50mm screwdriver bit
1 x No 2 Pozi 25mm screwdriver insert bit
A routing template that allows a router to create a hinge recess on a door.
Made from clear 8mm thick plastic.
Includes metal templates for 75mm and 100mm butt hinges.
Magnets in template frame to hold templates.
Cuts rounded corners which can be removed with a corner chisel or chisel.
Use on doors from 35mm to 44mm thick.
Requires 12mm diameter cutter and 30mm guide bush.
A user made batten 44mm x 34mm x 450mm is also needed.
This product includes:
1 x 75mm hinge template
1 x 100mm hinge template
This kit contains all the essential accessories to maximise the life of your router cutters, collets and router.
A collet and cutter care kit to increase the life of the cutters and the router collet. The kit includes a mini-diamond sharpening stone, a 60ml can of Trendicote, a 60ml can of Rust Buster, four brass brushes and a cutter care booklet.
The Rust Buster can be used to protect cutting tools against rust, frees sticky mechanisms, un-jams and lubricates. The Trendicote dry lubricant is sprayed on the routers cutters to reduce resin and dirt build up. It can also be used on jigs and machine tables to reduce friction.
The Diamond stone is ideal for honing router cutters when used with water. A small water bottle is supplied in the kit for this purpose.
The four brass brushes have sizes of 1/4", 8mm, 3/8" and 1/2" and are used to clean the inside of the relevant size collet. The brush is used to remove dirt and resin build up in the slots and bore of the collet.
Lastly the booklet gives full details on the care, storage and honing of router cutters.
1 x Mini-diamond sharpening stone
1 x Water bottle
4 x Brass brushes
1 x 60ml Trendicote
1 x 60ml Rust buster
For use in router tables where there is a limited router cutter shank available.
For use in router tables where there is a limited router cutters shank length available.
Precision machined one-piece steel body.
With a 1/2 inch shank, fitted with a multi-slit spring steel collet and collet nut.
Use at maximum speed 18000 RPM.
Increase cutter spindle length by 50mm.
Maximum tool diameter 50mm.
Maximum tool cut length 30mm.
Requires 19mm & 22mm A/F spanners.
Accessory collet and nut sets available for other shank diameters.
The two part Contractor Hinge Jig is a portable fully adjustable block template set designed for recessing hinges in wooden doors & frames using a plunge router.
It is easy to use with minimal setting-up time, completing the job both accurately & quickly.
Used on-site & in joinery shops to increase productivity with excellent results.
Fully adjustable apertures for fire door requirements and renovation work.
Can be used on both inside and outside doors, and on maximum 25mm thick fixed stops.
Ideal for fitting a new door in an old frame.
No need for marking out in the conventional way.
Quick & simple to set-up as the hinge is used as the pattern.
Clean & accurate recesses are achieved every time. Suitable for timber based doors & square butt hinges.
Use with a light duty plunge router with 1/4 inch collet.
Long reach router cutter required, 12mm diameter with 70mm overall length.
Adjustable edge guides with preset for hinge of 20mm, 25mm and 30mm
Unibase may be needed.
Patent No. GB2490139
T4EK router requires a ref. UNIBASE or special guide bush ref. GB/T4/160.
3 x Hinge sliding aperture block assemblies
4 x Bradawls (short blade)
1 x 16mm guide bush
1 x Carry case
A set of five long reach straight cutters with diameters of 1/4 inch to 5/8 inch suitable for use with the Mortise and Tenon Jig.
This product includes:
1 x C008X1/4TC - Straight 6.35mm dia x 25.4mm cut
1 x C012X1/4TC - Straight 7.9mm dia x 25.4mm cut
1 x C015X1/4TC - Straight 9.5mm dia x 31.8mm cut
1 x CO22X1/4TC - Straight 12.7mm dia x 31.8mm cut
1 x C026X1/4TC - Straight 15.9mm dia x 25.4mm cut
It completes traditional scribing chores with precision, speed and ease.
Quick and easy to use by remaining stable whilst scribing directly onto work-surfaces, flooring, shelves etc.
It works by running a wheeled scribe unit along an irregular feature.
The sprung pencil in its centre will accurately copy the profile directly onto the work-piece to be installed.
It can then be cut and fitted to the surface resulting in a perfect butt!
Four sizes of quick fit track wheels to cope with a variety of situations.
Design Reg. No. 3014615.
Guide bush guides the router when using a template.
Fits directly to Trend T3,T4,T5,T5 MK2, T9,T10 and T11, and some other light duty routers.
Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base.