Close
Filters

STRAIGHT BIT - 2 FLUTE - BOTTOM CUTTER 1/2" DIAMETER x 63.7 LONG - SHANK: 1/2"

STRAIGHT BIT - 2 FLUTE - BOTTOM CUTTER 1/2" DIAMETER x 63.7 LONG - SHANK: 1/2"

R660,00 incl VAT
- +
Manufacturer: Pro-tech Router Bits
Availability: In stock
SKU: TA15439
Manufacturer part number: KP115439
Write your own review
  • Product can be reviewed only after purchasing it
  • Only registered users can write reviews
*
*
  • Bad
  • Excellent
Customers who bought this item also bought
Picture of MAKITA RP1800X ROUTER

MAKITA RP1800X ROUTER

PPRP180
Powerful motor delivers smooth routing. Precise cutting depth adjustment. Ergonomically contoured knob style handles fit operator's hands perfectly. Linear ball bearing for super-smooth plunge action. Increased durability obtained by using larger size ball bearing on the drive-end of armature, labyrinth type retainers and fun. Double Insulation and Dust Collecting. Cast aluminium fence with precise adjustment for accurate cuts Template guide can be inserted without special tools.
R7 475,00 incl VAT
TREND LOCK JIG - SOUTH AFRICA

TREND LOCK JIG

TA-LJIG
Contractor jig with interchangeable templates for use with a plunge router to cut the mortise & face-plate recess for popular door locks. For most common sash mortises & deadlocks, with up to 3 inch deep mortises & a 7/8 inch or 1-inch face-plate. Deeper mortises can be achieved with a suitable size of auger bit. Fast, clean & accurate results on doors 34 mm to 58 mm thick, even in hardwood. Steel plates & body. An auger bit and drill are required to complete deep mortises. The jig requires a 1/2- inch plunge router with an 80 mm plunge, fitted with a 30 mm guide bush with 6 mm spigot & 12 mm diameter long reach cutter. A 1/4-inch plunge router can be used for the faceplate but will not achieve full depth of mortise. 1 x Guide Bush Collar 12 x Face Plate Templates 4 x Mortise Templates 6 x Spacer Fingers
Temp out of stock - R3 250,00 incl VAT
TREND UNIBASE - SOUTH AFRICA

Trend Unibase UNIB

TA-UNIB
The Unibase enables routers with non-standard guide bush fittings to accept the range of Trend guide bushes. It will fit directly to most routers. Line-up pin used with a 16 mm plastic bush to ensure concentricity of the cutter to the guide bush when fitting the sub-base. Suits collet sizes 1/4 inch, 8 mm, 12 mm and 1/2 inch. Instructions for fitting: The line-up pin fit into the collet and is plunged through the router base. The line-up bush is fitted into the Unibase and secured. This is then placed over the line-up pin and rotated to line up the fixing holes. The Unibase screws are tightened and then the line-up bush can be replaced with any choice of Trend guide bushes. These range from 10 mm up to 30 mm (GB10 - GB32). For larger diameter cutters a 40 mm guide bush (GB40) is available. Includes: 1 x Line up pin 8 & 12 mm shank 1 x Guide bush 16 mm 1 x Fixing screw pack
R692,86 incl VAT Temp out of stock - R519,64 incl VAT
JET JDR-34F RADIAL DRILL PRESS SOUTH AFRICA

JET JDR-34F RADIAL DRILL PRESS

WMJDR34
Jet JDR-34F - radial drilling machine, which gives the user greater freedom of adjustment. The drilling part of this model is fixed on a horizontal column and can move along the radius from the main one. This allows drilling a series of holes along a single line or adapting the machine for a specific job: increase the radius for drilling at a great distance from the edge of a large workpiece or reduce it to increase rigidity and accuracy. The mechanism for fixing the drilling part also allows you to tilt it at any angle between 90 ° to the left and 45 ° to the right, so that it is possible to make holes at an angle to the surface of the workpiece on a level table. The table itself is a round turntable with the possibility of changing the height of the installation and additional adjustment in the horizontal plane. The machine is equipped with a laser device for displaying the center of the forthcoming hole on the surface of the workpiece and a convenient quick-action chuck.
Temp out of stock - R13 250,00 incl VAT
Picture of TRIM BIT 1/2" DIAMETER X 2 LONG WITH BALL BEARING - SHANK: 1/2"

TRIM BIT 1/2" DIAMETER X 2 LONG WITH BALL BEARING - SHANK: 1/2"

TAKP120
R455,00 incl VAT