You have no items in your shopping cart.
Close
Filters

Planer Thicknesser

View as Grid List
Sort by
Display per page
Picture of JET 6LM  PLANER

JET 6LM PLANER

WMJP6LM
JJ-6L-M - planer with long cast iron tables, designed for amateur use. Due to the fact that it is executed on the same layout scheme as the professional Jet models, it is precise and convenient in operation. Structurally, it consists of two parts. In the bottom, playing the role of the pedestal-stand, is a single-phase asynchronous ("induction") motor with a power of a little more than a kilowatt and a shroud collecting hood with a 100-mm nozzle for connection to the exhaust system. The upper part consists of a cast-iron base where the planing shaft is located, and cast-iron work tables with the corresponding equipment consisting of a protective casing and the workpiece rest. Both tables are regulated in height by screw mechanisms, driven by handwheels. By moving the feeding (front) table, adjust the depth of planing, for which there is a corresponding marking; The receiver (rear) is moved only during the adjustment operations while the machine is serviced. The casting stop is cast-iron, with a mechanism for adjusting the tilt (it is possible in both directions). The selected position is locked by a threaded clip. The knife shaft is equipped with three knives, which allow re-sharpening. Their size is the same as that of the professional jet fuels with a similar planing width. FEATURES: Adjusting the planing depth Adjustable fence stop Adjustable blade guard Prefabricated tables of cast iron Planer stop made of cast iron
R18 200,00 incl VAT
Picture of JET JPT 410 PLANER/THICKNESSER

JET JPT 410 PLANER/THICKNESSER

WMJPT41
Jet JPT-410 - combined machine for planing and thicknessing with a working width of 407 mm. This value is quite large by the standards of professional thicknessing machines, and by the standards of jointing - and is typical for equipment of a higher industrial class. This combination of characteristics makes this model attractive not only from the point of view of saving the working space, but also extending the scope of application. The design of the machine is one of the most successful on the market: the wide use of massive cast iron parts guarantees accurate work without vibration, with the topmounting the top module rises completely and does not interfere with work or chip removal, a powerful three-phase motor ensures high productivity and reliability. Special attention deserves a convenient eccentric mechanism for adjusting the position of the tables, both the supply and the receiving, which is necessary when installing the helical shaft (option). When choosing between two specialized or one combined machine, it should be taken into account that these models are almost as accurate, convenient and efficient as specialized ones, but will require somewhat more frequent servicing of the thicknesser part in case of intensive operation. In the basic version, the JPT-410 is equipped with a three-knife planing shaft, as an alternative, a helical shaft is provided, which is equipped with hard-alloy cutting inserts. It is more reliable and easier to operate (no adjustments are necessary), but due to the consecutive entry of the knives into the workpiece it works quietly and with less vibrations. FEATURES: Possibility to install helical shaft Folding table Jointing Eccentric mechanism of depth adjustment Possibility to adjust the height of the receiving table Adjustable fence stop Adjustable blade guard Prefabricated tables of cast iron Planer stop from aluminum profile Thickening Disconnectable drive of feed shafts Adjusting the planing height of the rotating flywheel Model JPT-410 Article (400 V) 10000295T Consumed (output) power 4.5 (3.0) kW Rotational speed of the planer shaft 5500 rpm Diameter of planer shaft 70 mm The size of knives (LxWxT) 410 x 25 x 3.0 mm Number of knives 3 Maximum workpiece width 407 mm Diameter of extraction hose 127 mm Overall dimensions (LxWxH) 1660 x 920 x 1000 mm The weight 330 kg Jointing Depth of planing in one pass 0-3.0 mm Dimensions of the planer table (LxW) 1660 x 413 mm Dimensions of the planer stop (LxW) 1100 x 150 mm Tilt angle of the parallel stop 0-45 ° Thickening Feed speed 7 m / min Maximum workpiece height 225 mm Maximum depth of planing in one pass 3,5 mm Maximum permissible depth of planing in one pass over the whole width 1.5 mm Minimum length of workpiece 150 mm Length of thicknessing table 600 mm
Call for pricing
Picture of JET JPT-260M PLANER/THICKNESSER COMBINATION

JET JPT-260M PLANER/THICKNESSER COMBINATION

WM-260M
The Jet JPT-260 allows you to perform the operations of jointing and thicknessing on a professional level. Massive design with cast iron tables gives precision and vibration-free operation, a powerful asynchronous motor provides high performance and reliability. Jointing and thicknessing are performed as usual - no special working methods are required; readjustment takes almost no time. The upper planer module, which combines both the table and the planing depth adjustment mechanism, is fully folded (the previously made settings are not lost), the chip cover is flipped over. The layout with a convertible top gives advantages both in work (better overview, better work chip breaking), and when servicing the planer shaft, access to which is uncomplicated. Combined machine JPT-260 is optimal for use in workshops with a shortage of working space as a replacement for individual thicknesser and jointer. In comparison with them, it has a more loaded and complex design, the intensive operation of which may require increased maintenance costs. FEATURES: Folding table Jointing Eccentric mechanism of depth adjustment Adjustable fence stop Adjustable blade guard Prefabricated tables of cast iron Planer stop from aluminum profile Thickening Disconnectable drive of feed shafts Adjusting the planing height of the rotating flywheel Model JPT-260 Article (400 V) 10000289T Consumed (output) power 2.6 (1.7) kW Rotational speed of the planer shaft 5300 rpm Diameter of planer shaft 70 mm The size of knives (LxWxT) 260 x 25 x 3.0 mm Number of knives 3 Maximum workpiece width 256 mm Diameter of extraction hose 100 mm Overall dimensions (LxWxH) 1120 x 700 x 1000 mm The weight 170 kg Jointing Depth of planing in one pass 0-3.0 mm Dimensions of the planer table (LxW) 1120 x 260 mm Dimensions of the planer stop (LxW) 900 x 110 mm Tilt angle of the parallel stop 0-45 ° Thickening Feed speed 5.5 m / min Maximum workpiece height 225 mm Maximum depth of planing in one pass 3,5 mm Maximum permissible depth of planing in one pass over the whole width 1.5 mm Minimum length of workpiece 150 mm Length of thicknessing table 540 mm
R42 950,00 incl VAT
Picture of JET JPT-310 PLANER THICKNESSER COMBINATION 230V

JET JPT-310 PLANER THICKNESSER COMBINATION 230V

WMJPT31
Combined Jet Jet JPT-310 is optimal for use in workshops with limited space as a replacement for individual thicknesser and jointer. This model is in demand both by lovers of woodworking and by professionals. In addition to significant work space savings, the JPT-310 also provides cost savings when purchasing. According to the main characteristics and convenience of work, this combined machine is not inferior to individual thicknesser and jointer. Long and massive cast-iron tables create a base sufficient for working with parts up to 2-3 meters long. Concerning the specialized machine, the fence stopper is slightly easier: it is not made of cast iron but of an aluminium profile. On the other hand, these models have a rare advantage: a convenient eccentric height adjustment has not only a feeding but also a receiving table. This is necessary, first of all, when replacing the planer shaft with helical, the cutting inserts of which are not adjustable in height. To move from joining to thicknessing, it is sufficient to raise the upper module consisting of tables and frame and reset the chipper case, the previously made settings do not get knocked off. This design gives advantages both in operation and in servicing the machine. The shaft helical, available for Jet JPT-310 as an option, is widely in demand among professionals. Its main advantages are low noise level at work, clean cutting of knots, no wood breaks, long service life of carbide tetrahedral blades, no need for sharpening and adjustment. FEATURES: Possibility to install the helical shaft Folding table Jointing Eccentric mechanism of a depth adjustment Possibility to adjust the height of the receiving table Adjustable fence stop Adjustable blade guard Prefabricated tables of cast iron Planer stop from aluminium profile Thickening A disconnectable drive of feed shafts Adjusting the planing height of the rotating flywheel
R50 800,00 incl VAT
JET PLANER THICKNESSER JPT310HH 230V

JET JPT310HH PLANER/THICKNESSER COMBINATION

WMJPT3H
Combined Jet JPT-310HH is optimal for use in workshops with limited space as a replacement for individual thicknesser and jointer. The model is in demand both by lovers of woodworking and by professionals. In addition to significant savings in the working space, the combined machine also provides savings in purchasing.
Call for pricing
Picture of JET JPT-410HH PLANER THICKNESSER

JET JPT-410HH PLANER THICKNESSER

WM0296T
The JPT-410HH Jet is a helical combination machine for surfacing and thicknessing with a 407 mm working width. This value is quite large by the standards of professional jointing machines, and by the standards of jointing - and is entirely characteristic of equipment of a higher industrial class. This combination of characteristics makes the model attractive not only in terms of saving working space, but also expanding the scope. The machine design is one of the most successful on the market: the extensive use of massive cast-iron parts ensures accurate work without vibrations; when jointing, the upper module rises completely and does not interfere with work or stripping, a powerful three-phase motor ensures high performance and reliability. Special attention is given to a convenient eccentric mechanism for adjusting the position of the tables, both the feed and the receiver, which is necessary when installing the helical shaft (optional). The helical shaft included in the basic equipment is equipped with carbide cutting inserts. It is safer and easier to operate (no adjustments are needed), and due to the sequential entry of knives into the work piece, it works quieter and with less vibrations.
Call for pricing
jet-jwp12-professional-benchtop-portable-12-thicknesser-planer-1800w

JET JWP-12 PORTABLE THICKNESSER Planer

WMJWP12
Designed especially for the hobby woodworker, the JWP-12 is compact and very capable. Its powerful 1,800W motor quickly removes material up to 2.5mm thick with each pass. The block is fitted with two resharpenable HSS blades and gives 18,000 cuts/min, this coupled with the feed speed of 7m/min ensures an excellent ripple-free finish.
Call for pricing
Picture of MAKITA 2012NB 304MM PLANER

MAKITA 2012NB 304MM PLANER

PP-2012
Compact and lightweight for easier transport. Unique feeding mechanism assures smoother finish with minimal snip on stock. 4-post design and diagonal cross supports for stability. Double Insulation.
R15 285,00 incl VAT
Picture of TOOLMATE PRO 10'' PLANER THICKNESSER 2000W

TOOLMATE PRO 10'' PLANER THICKNESSER 2000W

WM-260S
Call for pricing
Picture of TOOLMATE TMPTB260X COMBINATION PLANER/THICKNESSER

TOOLMATE TMPTB260X COMBINATION PLANER/THICKNESSER

WMPTB60
This combination Planer/Thicknesser is a light industrial rated machine that is used to plane wood to the correct width and thickness.Because it is also a surfacer, it allows the user to get rid of twists, cups and bows prior to thicknessing. Made mainly from cast iron, it’s a very heavy machine and an excellent choice for the serious woodworker. The mass of the machine dampens much of the vibration and this, together with the helical head type cutter block spinning at 4,000rpm, results in a very clean finish, especially on cross grained wood.The infeed and outfeed rollers can be deactivated when surfacing-resulting in less wear and more power to the cutterhead.The aluminium tilting fence offer exceptional accuracy and stability and is adjustable from 0⁰(90⁰)-45⁰ The dust extraction hood is positioned underneath the table for surfacing and must swing upwards when thicknessing. Both the top tables must be tilted out of the way when thicknessing. The machine is fitted with anti kickback fingers to avoid any kickback when thicknessing. The helical head cutterblock is fitted with 6 rows of cutters, arranged in a helical spiral. Cutters are staggered in such a way that each cutting edge overlaps the one in front of it, resulting in a very smooth finish. These 14 x14mm x 1.5mm cutters each has 4 cutting edges and can easily be swiveled to reveal a new cutting edge in case they becomes blunt or damaged (Cutters are throw-away type and can't be re-sharpened) . Both top tables are independently adjustable to ensure that they remain co-planer.The machine is fitted with electrical safety switches to avoid accidental starting without the dust extraction hood in place. The ticknessing table has a locking lever that will ensure stability in the thickness setting. Machine must be used with a dust collector. NB) Apply wax to the thicknessing table on a regular basis.
R33 550,00 incl VAT
Picture of TOOLMATE TMPTB260 COMBINATION PLANER/THICKNESSER

TOOLMATE TMPTB260 COMBINATION PLANER/THICKNESSER

WMPTB26
This combination Surfacer/Thicknesser (also called jointer/planer) is a light industrial rated machine with accurately ground, cast iron planing and thicknessing tables, together with a cast iron main frame. The mass of the machine dampens much of the vibration and this, together with a 3 knife cutter block spinning at 4,000rpm, results in a very clean finish on the workpiece.The infeed and outfeed rollers can be deactivated when surfacing-resulting in less wear and more power to the cutterhead. The aluminium tilting fence offer exceptional accuracy and stability when planing the edge of timber and can be set to any angle from 45⁰- 90⁰. The built-in dust extraction hood is positioned underneath the top table when surfacing and is swung up when thicknessing. Both of the tables must be tilted out of the way when thicknessing. The 3 knives in the cutter block can be is set using the excellent gauge supplied, or it can be done with any straight piece of wood using the traditional drag method with the back table as reference. Both tables are independently adjustable and electrical safety switches prevent accidental starting when the cutter head is exposed. The ticknessing table has a locking lever that will keep it secure on any height when thicknessing. The machine is also fitted with anti-kickback fingers when in hicknessing mode. Tip: Apply wax to the tables on a regular basis. This is especially important when thicknessing timber. It allows the wood to glide through the planer without sticking to the bottom surface. Any good quality furniture wax will do.
R21 100,00 incl VAT

Filter by:

Clear All
Min: R8 450,00 Max: R105 000,00
R8450 R105000